''
  • -$40.00
NV-Ton NVM-P wind  copper
NV-Ton NVM-P wind  brass
NV-Ton NVM-P wind  brass
NV-Ton NVM-P wind  brass
NV-Ton NVM-P wind  brass
NV-Ton NVM-P wind  brass
NV-Ton NVM-P wind  brass
NV-Ton NVM-P wind  copper
NV-Ton NVM-P wind  copper
NV-Ton NVM-P wind  copper
NV-Ton NVM-P wind  copper
NV-Ton NVM-P wind  copper
NV-Ton NVM-P wind  brass
NV-Ton NVM-P wind  brass
NV-Ton NVM-P wind  copper
NV-Ton NVM-P wind  brass
NV-Ton NVM-P wind  brass
NV-Ton NVM-P wind  brass
NV-Ton NVM-P wind  brass
NV-Ton NVM-P wind  brass
NV-Ton NVM-P wind  brass
NV-Ton NVM-P wind  copper
NV-Ton NVM-P wind  copper
NV-Ton NVM-P wind  copper
NV-Ton NVM-P wind  copper
NV-Ton NVM-P wind  copper
NV-Ton NVM-P wind  brass
NV-Ton NVM-P wind  brass

NV-Ton NVM-P wind brass

NV-Tone The NVM-P Wind Brass Mic is a mini condenser microphone for picking up the sound of brass instruments. Perfectly transmitting a powerful and deep low-frequency range of the instrument, punching highs, not protruding mids. All of this is available from tubas and sousaphones to horns and sopranos, where you will be pleasantly surprised by the dynamics and balance across the entire spectrum, and also boast excellent resistance to feedback. Easy to install, doesn`t requiring any milling operation with the instrument. Due to the optimal length and flexibility of the microphone neck, you can choose any position.

1242
$179.00 $219.00 -$40.00
Tax included
 

Equipment:

  • Microphone with flexible neck
  • High quality 2.5m audio cable
  • XLR Inverter Connector
  • Reliable, reusable fastening tape (3 pcs.)
  • Durable and stylish ECO leather case
  • Manual

 

DEMO SOUND 1

 

 

DEMO SOUND 2

 

 

DEMO SOUND 3

 

 

DEMO SOUND 4

 

 

it is recommended to listen with headphones

Frequency range
20 ~ 20000 Hz
Sensitivity
-32 ±3 dB
Signal-to-noise ratio
74 dB
Operating voltage range
1 ~ 10 VDC
Neck length
5.2″ inch
Directivity
omni-directional
Material
aerospace-grade 6061 aluminum

Installation and operation manual

– select the appropriate place on the instrument

– make sure, that the microphone installed in this place will not interfere with the playment (bow, pick, hand etc.)
– Stick the fixing tape on a clean, prepared surface only
– Attach the microphone to the strap tape, then adjust the position

– Connect with cable to Your audio device (combo, audio interface, mixer etc.)

 

For internal only

– select the appropriate place on the instrument

– make sure that the microphone, installed in this place, will not interfere with the playment (bow, pick, hand etc.)

– remove the factory button strap (if it is missing, a hole must be made in the appropriate place, observe safety rules!)

– If necessary, enlarge the hole (when working with tools, observe the safety rules!)

– install the connector in to the hole and secure it with a nut

– Stick the fixing tape on a clean, prepared surface only

– Attach the microphone to the strap, and then adjust the position

– fix the wires inside the instrument with adhesive tape

 Connect with cable to Your audio device (combo, audio interface, mixer etc.)

Product added to compare.